برد کنترلر کرونوس CronosMaker 3Axis GRBL مخصوص راه اندازی CNC، لیزر و حکاکی سازگار با GRBL
این برد یک کنترلر سه محوره است.از این برد می توانید برای کنترل دستگاه های CNC، دستگاه های لیزر و حکاکی استفاده نمایید.
این برد بر اساس آردینو نانو طراحی شده است. پشتیانی از دو سوکت محور Y، مناسب برای استفاده در دستگاه لیزر های حکاکی و انواع سی ان سی سه محور که اسپیندل های 300 وات را پشتیبانی می کند.
این برد بر اساس آردینو نانو طراحی شده است. پشتیانی از دو سوکت محور Y، مناسب برای استفاده در دستگاه لیزر های حکاکی و انواع سی ان سی سه محور که اسپیندل های 300 وات را پشتیبانی می کند.
![](https://www.parmanshop.ir/image/data/electrical/grbl-cnc-controller-control-board-3axis-002.jpg)
Nano 3Axis Control Board is an Arduino Nano based 3 Axises Motion control system, can be used
for Laser Engraving Machine, Drawer Machine, CNC Engraving Machine etc.
--Double y-axis, all-round use, XYZ or XYY.
--Stepper drive setup subdivision.
--Integrated 3 A4988 drivers, directly connect to the four-wire stepper motor.
--Support Laser or Spindle(300W).
--Support 12V, 5V with TTL and without TTL laser.
--Adjustable driver subdivision.
--Support the XYZ limit switch, probe interface.
--Support external Offline Controller(Optional).
--A4988 can be replaced with 8825 drivers.
--Can Connect 300W Spindle/Offline/Limit/2Pin Laser/3Pin Laser/Fan
Please note the positive and negative poles, make the right connection. Its not seller's responsibility if the fault was from this.
WHAT IS SPECIAL:
Designed for 3 Axis CNC router 1610; 2418; 3018, Managed by Software 0.9J USB GRBL Controller
Input voltage: 12-36V; Laser output: 12V ; 775 motor output 24V
Stepper motor driver: A4988 /Support stepper motor: 12V, maximum current of 2A ; recommended within 1.5A ; Support stepper motor 42, 57
Laser output 2P/3P supports pwm TTL function
Master chip: atmel 328P (arduino nano)
TECHNICAL DETAILS:
Laser output: 12V ; 775 motor output 24V
Laser output 2P/3P supports pwm TTL function
Support offline, Bluetooth function, Support the xyz limit switch, probe interface.
Connection interface: USB (USB-CH340)
Software: GRBL controller
Input voltage: 12-36V
Master chip: atmel 328P (arduino nano)
Stepper motor driver: A4988
Spindle drive chip: MOSFET (recommendation 12~36V, current : within 10A )
Spindle PWM speed: Support
Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Adapter 5.5-2.5mm DC interface
Tool set: Support
Limit Switch: Support
17.Double y-axis, all-round use,XYZ or XYY.
A4988 can be replaced with 8825 driver.
Product include:
1*Control board
1*USB Data line
for Laser Engraving Machine, Drawer Machine, CNC Engraving Machine etc.
--Double y-axis, all-round use, XYZ or XYY.
--Stepper drive setup subdivision.
--Integrated 3 A4988 drivers, directly connect to the four-wire stepper motor.
--Support Laser or Spindle(300W).
--Support 12V, 5V with TTL and without TTL laser.
--Adjustable driver subdivision.
--Support the XYZ limit switch, probe interface.
--Support external Offline Controller(Optional).
--A4988 can be replaced with 8825 drivers.
--Can Connect 300W Spindle/Offline/Limit/2Pin Laser/3Pin Laser/Fan
Please note the positive and negative poles, make the right connection. Its not seller's responsibility if the fault was from this.
WHAT IS SPECIAL:
Designed for 3 Axis CNC router 1610; 2418; 3018, Managed by Software 0.9J USB GRBL Controller
Input voltage: 12-36V; Laser output: 12V ; 775 motor output 24V
Stepper motor driver: A4988 /Support stepper motor: 12V, maximum current of 2A ; recommended within 1.5A ; Support stepper motor 42, 57
Laser output 2P/3P supports pwm TTL function
Master chip: atmel 328P (arduino nano)
TECHNICAL DETAILS:
Laser output: 12V ; 775 motor output 24V
Laser output 2P/3P supports pwm TTL function
Support offline, Bluetooth function, Support the xyz limit switch, probe interface.
Connection interface: USB (USB-CH340)
Software: GRBL controller
Input voltage: 12-36V
Master chip: atmel 328P (arduino nano)
Stepper motor driver: A4988
Spindle drive chip: MOSFET (recommendation 12~36V, current : within 10A )
Spindle PWM speed: Support
Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Adapter 5.5-2.5mm DC interface
Tool set: Support
Limit Switch: Support
17.Double y-axis, all-round use,XYZ or XYY.
A4988 can be replaced with 8825 driver.
Product include:
1*Control board
1*USB Data line
3*A4988 Driver